VENTS PA 03 W2

Print version Save in PDF format

Maximum capacity - 3260 m³/h.

Add to project

Add to compare

Description
Characteristics
Capacity diagram
Downloads
Dimensions
Additional characteristics
Designation key
Accessories

Description

DESCRIPTION
The PA unit is a ready to use ventilation unit for air filtration, warming and supply to the room.
CASING
Steel casing covered with aluzinc coating internally filled with 50 mm heat- and sound-insulating layer made of mineral wool.
FILTER
Integrated panel G4 filter ensures sufficient supply air purification (optionally F7).
HEATER
The PA units are equipped with electric (PA…E model) or water (PA…W model) heater. Depending on the required heating capacity the water heaters are available in two-, three- or four-row modifications.	The water heaters are designed for max. operating pressure 1.0 MPa (10 bar) and max. operating temperature 95 °C of the heat medium.
FAN
The unit is equipped with a direct-driven centrifugal fan with backward curved blades and external rotor motor.	The fan configuration ensures the best operating characteristics: high air capacity and efficiency combined with low noise level.
MOUNTING
The unit is designed for indoor installation either on the floor, on the wall or under the ceiling by means of a seat angle with inserted vibration-damping element or attached to a wall with brackets. The unit can be mounted either in service spaces or in main premises above the suspended ceiling, in the pocket or the unit can be placed directly in the room. All the electrical connections are performed through the terminal box placed in the connection box.	PA supply units are supplied with the fastening brackets to facilitate mounting. The unit can be mounted in any position but the vertical one with vertical air downstream because the electrical heating elements are not allowed under the fan. Access for the unit maintenance and filter cleaning shall be provided. The unit design enables to lead the water heater pipes to the right or to the left while mounting. The pipes are directed on the right on supply air side by default.
CONTROL AND AUTOMATION
The supply units are available in two modifications: No control system. Customer-defined and customer-selected automation system. Integrated control and automation system for speed (air capacity) control and setting supply air temperature. The unit may be remotely controlled from the external control panel fixed on wire.
PA…W control and protection functions
control from the control panel: switching the unit on/off, fan speed selection (low/medium/high speed), selecting heating/cooling modes (if connected to duct cooler); maintaining supply air temperature set from the control panel by controlling the circulation pump and actuating the heat medium regulating valve; input from the heat medium flow switch (pump alarm); safe start-up/ shutdown of the fans, warming up of the water heater before start-up; return heat medium temperature control when the fan is off;	freezing protection of the water heating coils by the exhaust temperature sensor and the return heat medium temperature sensor; control of the compressor and condensing unit of the water cooler by the room temperature sensor (for the models equipped with a duct air cooler); filter clogging degree with differential pressure sensor; actuating the external air damper with a return spring; unit shut down at signal from the fire alarm system.

SUPPLEMENTARY EQUIPMENT

The mixing units USWK are recommended for smooth supply air temperature regulation in the units equipped with water heaters.
The mixing unit USWK with three-way heat medium regulating valve and circulation pump provides smooth heating capacity regulation and minimizes the water heater freezing danger.
To disable uncontrollable air flow when the fan is off it is recommended to install the air damper with servo actuator from outside at the unit inlet.

To protect the water heater against cold intake air in case of power failure for the units with water heaters it is recommended to install the air damper with a return spring.
For attenuation of sound generated by the fan it is recommended to install the duct silencer (refer SR).
For vibration absorbing it is recommended to install the flexible anti-vibration connectors (refer VVG) on both sides of the unit.

Characteristics

Parameter	PA 03 W2	Measurement unit
Frequency	50	Hz
Phase	3	˜
Voltage	400	V
Fan current	2.4	A
Maximum fan power	1330	W
Air capacity	3260	m³/h
Maximum air capacity	3260	m³/h
Total unit power	1330	W
Total unit current	2.4	A
RPM	2730	min^-1
Filter	G4 (F7) pocket type*	-
Transported air temperature	-25 ... +45	°С
Sound pressure level at 3 m distance	57	dBА
Heating	water heating	-
Casing material	aluzinc	-
Insulation	50 mm mineral wool	-
Width	600	mm
Connected air duct diameter	600х350	mm
Number of water (glycol) coil rows	2	-
Mass	91	kg
Height	350	mm
Number of rows in water heater	2-двухрядный	-
Duct	for rectangular air ducts	-

Capacity diagram

Selection method:
Air flow:
Pressure:

Operating point

Air flow: --
Pressure: ---

Files archieve

Downloads

Name

Download

Show

Brochure "VENTS PA...E, PA...W" (pdf 5.07Mb)

Download high quality image "VENTS PA...W (ErP 2016, 2018)" (psd 4.09Mb)

User's manual "VENTS PA...W. Unit without automation block" (pdf 1.44Mb)

User's manual "Control and automation block for VENTS PA...W" (pdf 1.61Mb)

User's manual "Control system for air supply and air handling units based on Freemax controllers and AC208A2 sensor control panels" (pdf 7.21Mb)

Download image "VENTS PA...W (ErP 2016, 2018)" for your website (png 367.25Kb)

Dimensions

Characteristics

Parameter	Value	Measurement unit
B	600	mm
B3	744	mm
B1	620	mm
L	1252	mm
H	350	mm
L1	1212	mm
H2	500	mm
B2	787	mm
H1	370	mm

Additional characteristics

Sound-power level		Gen	Octave-frequency band [Hz]
Sound-power level		Gen	63	125	250	500	1000	2000	4000	8000
L_WA to inlet	dBA	71	57	71	66	57	51	50	56	56
L_WA to outlet	dBA	78	57	70	73	73	70	67	64	53
L_WA to environment	dBA	59	39	58	62	51	44	52	49	46

Designation key

Series	Unit standard size	Heater type	Row number of the heater	Integrated control system
VENTS PA	01; 02; 03; 04	W: water	2: two rows; 3: three rows; 4: four rows	_: no control system LCD: integrated automation with A16 (PA..E) or A13 (PA..W) control panel

Accessories

Type	G4 replaceable filter F	F7 replaceable filter	Filter type
PA 01 W2	SFK 474x269x27 G4	SFK 474x269x27 F7	pocket filter
PA 01 W4
PA 02 W2	SFK 538x342x27 G4	SFK 474x269x27 F7	pocket filter
PA 02 W4
PA 03 W2	SFK 637x395x27 G4	SFK 637x395x27 F7	pocket filter
PA 03 W4
PA 04 W2	SFK 737x441x27 G4	SFK 737x441x27 F7	pocket filter
PA 04 W3